不銹鋼蹲便器半成品是列車上的配備設施,它是否能達到很好的應用,不光取決于產品本身的質量,正確的安裝也很重要.

安裝時需要注意:

1、XKD-818不銹鋼蹲便器半成品全面與混凝土接觸的部分要填上瀝青或油氈等彈性材料,不然因水泥膨脹導致便器碎裂.

2、用加熱溶解的瀝青涂飾時,應避免便器受熱導致碎裂.

3、便器安設應嚴格按闡明書駕馭施工,不然釀成便器碎裂.

4、XKD-818不銹鋼蹲便器半成品進水沖刷裝置緊要有球閥、高水箱沖刷、電磁感覺沖刷閥、延時沖刷閥、手動沖刷閥等.

5、安裝和利用時避免猛力撞擊.

XKD-818不銹鋼蹲便器半成品通常分帶彎和不帶彎兩種,帶彎的高度一般為300mm左右,不帶彎的高度一般為200mm左右.蹲便器安裝高度要根據具體使用哪種蹲便器來決定,從而來確定下水管道的預留高度.蹲便器安裝高度如果確實要偏差的話,要求水泥臺一般不低于蹲便器高度的3公分,蹲便器站壁一般為3—5公分厚,通常安裝蹲便器是將蹲便器與水泥臺平行的.

XKD-818不銹鋼蹲便器半成品安裝注意事項如下:

1、在安裝不銹鋼便器時,對于蹲便器與混凝土接觸的所有部分,都要填上瀝青或油氈一類的彈性材料,否則很容易發生因水泥膨脹而導致出現蹲便器變形的問題.此外,在用加熱溶解的瀝青等對蹲便器進行涂飾時,也應該要注意防止蹲便器受熱而導致變形.

2、安裝蹲便器應該嚴格按照相關使用說明書進行操作施工.蹲便器的進水沖洗裝置主要有球閥、高水箱沖洗、電磁感應沖洗閥、延時沖洗閥、手動沖洗閥等,安裝之時需要一一對應好,才能達到良好的使用效果.在安裝和使用蹲便器之時要注意避免猛力撞擊.